Found a place to get our AXEL's straightened

denver dude · **Joined:** September 19th, 2009, 9:31 pm **Posts:** 785

I talked to Dennis at SL Harbert Machine and weld 5635 Franklin st Denver, CO. 303-296-7355, and he told me that they straighten axel's. They just did an axel on a shifter cart. He said to give them a call, and he guarantee's his work or it does not cost anything. They came highly recommended by quite a few different places. Good information. Later

quadnut20 · **Posted:** February 18th, 2010, 8:29 am

denver dude wrote:

I talked to Dennis at SL Harbert Machine and weld 5635 Franklin st Denver, CO. 303-296-7355, and he told me that they straighten axel's. They just did an axel on a shifter cart. He said to give them a call, and he guarantee's his work or it does not cost anything. They came highly recommended by quite a few different places. Good information. Later

Did you bend an axle ??It`s good to know though :rockon:

denver dude · **Joined:** September 19th, 2009, 9:31 pm **Posts:** 785

I have not bent an axel that I know of. Had someone ask me and did some research, found a local place. :cheers:

If I do bend one, I know who I am going to take it to.

preston660r · **Posted:** February 19th, 2010, 11:48 pm

ya bent axels no fun i bent a lonestar plus 2 axel, and its bent all the way into the carrier. :banghead:

quadnut20 · **Posted:** February 20th, 2010, 1:10 pm

denver dude wrote:

I have not bent an axel that I know of. Had someone ask me and did some research, found a local place. :cheers:

If I do bend one, I know who I am going to take it to.

Hell with your money you could buy us all a new one :worship:

HA HA

sandwilly · **Posted:** February 20th, 2010, 3:00 pm

No he dosent have a job so dad gets to pay for a new one or try and get that one straghtend :stick:

quadnut20 · **Posted:** February 20th, 2010, 3:04 pm

sandwilly wrote:

No he dosent have a job so dad gets to pay for a new one or try and get that one straghtend :stick:

I feel your pain :thumbsup:

I have 4 boys :crazy:

With grand kids :cheers:

denver dude · **Joined:** September 19th, 2009, 9:31 pm **Posts:** 785

preston660r wrote:

ya bent axels no fun i bent a lonestar plus 2 axel, and its bent all the way into the carrier. :banghead:

Sucks bro. At least you have one of the coolest dad's out there. :rockon:

Welcome to the site :clap:

preston660r · **Posted:** February 20th, 2010, 5:24 pm

you no i actualy get the quad as is for a birthday prestent and i had to pay for tires and stuff like that. its a raptor 660r all modded out its pritty sweet. :bump:

and sandwilly is acualy my dad he heard about the site from dd and been hooked since

denver dude · **Joined:** September 19th, 2009, 9:31 pm **Posts:** 785

Yes, you and your dad have really nice 660's. Appreciate you guys joining QW. Later, DD

denver dude · **Joined:** September 19th, 2009, 9:31 pm **Posts:** 785

Update, I dropped off a couple of axel's today at Harbert machine. I went with Dennis out to the shop where he put them in the lathe and checked both of them. I must say that Harbert knows their stuff, and I was impressed with their service. :clap:

preston660r · **Posted:** February 28th, 2010, 2:39 pm

Hey i just got my axsel back and i must say it looks amazing i would most definately recomend him. for two axsels it was 145$ :clap:

denver dude · **Joined:** September 19th, 2009, 9:31 pm **Posts:** 785

Right on Preston, happy to see they met your standards there at Harbert.

Found a place to get our AXEL's straightened

Who is online